Voltage Controlled Oscillator - Jack Version: Difference between revisions

From MMM Wiki
Jump to navigationJump to search
No edit summary
 
(18 intermediate revisions by 3 users not shown)
Line 1: Line 1:
[[Image:VCO-J.jpg]]
[[Image:VCO-J-3.jpg|400px||VCO-J]]


There are two versions of the VCO. Both are identical oscillators. The difference between them is the panel output and switching configurations.
There are two versions of the VCO. Both are identical oscillators. The difference between them is the panel output and switching configurations.
Line 5: Line 5:
'''For both VCO versions:'''
'''For both VCO versions:'''


The Lin Kbd CV In jack allows for 1 volt/ octave control of the oscillator root frequency.
The 1V/O In jack allows for 1 volt/ octave control of the oscillator root frequency.


The exponential amplifier is incorporated into the VCO module.
The exponential amplifier is incorporated into the VCO module.


The Lin Kbd Out jack allows for a buffered linear CV that controls the VCO to be "tapped"
The Lin Out jack allows for a buffered linear CV that controls the VCO to be "tapped"
and used for a control voltage elsewhere in the system. Typical use is for connecting to another VCO without tying up a buffer channel.
and used for a control voltage elsewhere in the system. Typical use is for connecting to another VCO without tying up a buffer channel.


Line 26: Line 26:
Master Octave switch transposes the oscillator up or down 1 octave.
Master Octave switch transposes the oscillator up or down 1 octave.


The "V/O" trim is available for scaling adjustment from the front panel.
The "V/O" Adj is available for scaling adjustment from the front panel.


'''For the 'S' (switched) version:'''
'''For the 'J' (Jack) version:'''
 
All of the available waveforms are present at jacks. (Triangle, Saw 0, Saw +1, Square 0, Square -1 and Square -2.)
 
 
== Availability ==
 
This module is no longer available.


Square out has an independent switch that drops the square wave down -1 or -2  
VCO 2 coming soon!
octaves from the triangle output frequency.


Sawtooth has an independent switch that raises the sawtooth frequency up 1 octave
'''VCO2 has all of the standard VCO features and includes the following features:'''
from the triangle output frequency.


The octave switches on the individual waveforms allow for up to a 4 octave spread
'''A:''' Sine waveform output
of waveform outputs from a single oscillator. All in sync and in tune with each other.


'''For the 'J' (Jack) version:'''
'''B:''' Manual PW on main square output
 
'''C:''' PWM input and attenuator for main square wave output.
 
'''''7 simultaneous waveform outputs spreading 4 octaves!'''''
 
'''$ TBD'''
 
== Info ==
 
'''Current draw of version 1:'''
 
Initial warm up (first minute):
 
V+= 93.6mA
 
V-= 42.2mA
 
 
'''After warm up:'''
 
V+= 73.2mA


All of the available waveforms are present at jacks. (Triangle, Saw 0, Saw +1, Square 0, Square -1 and Square -2.)
V-= 42.0mA

Latest revision as of 11:24, 30 December 2016

VCO-J

There are two versions of the VCO. Both are identical oscillators. The difference between them is the panel output and switching configurations.

For both VCO versions:

The 1V/O In jack allows for 1 volt/ octave control of the oscillator root frequency.

The exponential amplifier is incorporated into the VCO module.

The Lin Out jack allows for a buffered linear CV that controls the VCO to be "tapped" and used for a control voltage elsewhere in the system. Typical use is for connecting to another VCO without tying up a buffer channel.

The Master Tune allows for approximately +/- 1 octave continuous adjustment of the oscillator root frequency.

The Fine Tune allows for approximately +/- 3 semi-tone adjustment of the oscillator root frequency.

Mod In jack provided for an oscillator modulation source CV input.

Mod Amount control for variable control of the modulation CV effect on the oscillator frequency.

Simultaneously available Triangle, Square and Sawtooth waveform outputs.

Master Octave switch transposes the oscillator up or down 1 octave.

The "V/O" Adj is available for scaling adjustment from the front panel.

For the 'J' (Jack) version:

All of the available waveforms are present at jacks. (Triangle, Saw 0, Saw +1, Square 0, Square -1 and Square -2.)


Availability

This module is no longer available.

VCO 2 coming soon!

VCO2 has all of the standard VCO features and includes the following features:

A: Sine waveform output

B: Manual PW on main square output

C: PWM input and attenuator for main square wave output.

7 simultaneous waveform outputs spreading 4 octaves!

$ TBD

Info

Current draw of version 1:

Initial warm up (first minute):

V+= 93.6mA

V-= 42.2mA


After warm up:

V+= 73.2mA

V-= 42.0mA

Retrieved from "https://mattsonminimodular.com/wiki/index.php?title=Voltage_Controlled_Oscillator_-_Jack_Version&oldid=1483"