Voltage Controlled Oscillator - Jack Version: Difference between revisions

From MMM Wiki
Jump to navigationJump to search
(New page: Lin Kbd CV In jack allows for 1 volt/ octave control of the oscillator root frequency. The exponential amplifier is incorporated into the VCO module. Exp Kbd Out jack allows for the expo...)
 
 
(23 intermediate revisions by 5 users not shown)
Line 1: Line 1:
Lin Kbd CV In jack allows for 1 volt/ octave control of the oscillator root frequency.
[[Image:VCO-J-3.jpg|400px||VCO-J]]
 
There are two versions of the VCO. Both are identical oscillators. The difference between them is the panel output and switching configurations.
 
'''For both VCO versions:'''
 
The 1V/O In jack allows for 1 volt/ octave control of the oscillator root frequency.


The exponential amplifier is incorporated into the VCO module.
The exponential amplifier is incorporated into the VCO module.


Exp Kbd Out jack allows for the exponential CV that controls the VCO to be "tapped"
The Lin Out jack allows for a buffered linear CV that controls the VCO to be "tapped"
and used for a control voltage elsewhere in the system.
and used for a control voltage elsewhere in the system. Typical use is for connecting to another VCO without tying up a buffer channel.


Master Tune allows for approximately +/- 1 octave continuous adjustment of the  
The Master Tune allows for approximately +/- 1 octave continuous adjustment of the  
oscillator root frequency.  
oscillator root frequency.  
The Fine Tune allows for approximately +/- 3 semi-tone adjustment of the oscillator root frequency.


Mod In jack provided for an oscillator modulation source CV input.
Mod In jack provided for an oscillator modulation source CV input.
Line 18: Line 26:
Master Octave switch transposes the oscillator up or down 1 octave.
Master Octave switch transposes the oscillator up or down 1 octave.


Square out has an independent switch that drops the square wave down -1 or -2  
The "V/O" Adj is available for scaling adjustment from the front panel.
octaves from the triangle output frequency.
 
'''For the 'J' (Jack) version:'''
 
All of the available waveforms are present at jacks. (Triangle, Saw 0, Saw +1, Square 0, Square -1 and Square -2.)
 
 
== Availability ==
 
This module is no longer available.
 
VCO 2 coming soon!
 
'''VCO2 has all of the standard VCO features and includes the following features:'''
 
'''A:''' Sine waveform output
 
'''B:''' Manual PW on main square output
 
'''C:''' PWM input and attenuator for main square wave output.
 
'''''7 simultaneous waveform outputs spreading 4 octaves!'''''
 
'''$ TBD'''
 
== Info ==
 
'''Current draw of version 1:'''
 
Initial warm up (first minute):
 
V+= 93.6mA
 
V-= 42.2mA
 
 
'''After warm up:'''


Sawtooth has an independent switch that raises the sawtooth frequency up 1 octave
V+= 73.2mA
from the triangle output frequency.


The octave switches on the individual waveforms allow for up to a 4 octave spread
V-= 42.0mA
of waveform outputs from a single oscillator. All in sync and in tune with each other.

Latest revision as of 11:24, 30 December 2016

VCO-J

There are two versions of the VCO. Both are identical oscillators. The difference between them is the panel output and switching configurations.

For both VCO versions:

The 1V/O In jack allows for 1 volt/ octave control of the oscillator root frequency.

The exponential amplifier is incorporated into the VCO module.

The Lin Out jack allows for a buffered linear CV that controls the VCO to be "tapped" and used for a control voltage elsewhere in the system. Typical use is for connecting to another VCO without tying up a buffer channel.

The Master Tune allows for approximately +/- 1 octave continuous adjustment of the oscillator root frequency.

The Fine Tune allows for approximately +/- 3 semi-tone adjustment of the oscillator root frequency.

Mod In jack provided for an oscillator modulation source CV input.

Mod Amount control for variable control of the modulation CV effect on the oscillator frequency.

Simultaneously available Triangle, Square and Sawtooth waveform outputs.

Master Octave switch transposes the oscillator up or down 1 octave.

The "V/O" Adj is available for scaling adjustment from the front panel.

For the 'J' (Jack) version:

All of the available waveforms are present at jacks. (Triangle, Saw 0, Saw +1, Square 0, Square -1 and Square -2.)


Availability

This module is no longer available.

VCO 2 coming soon!

VCO2 has all of the standard VCO features and includes the following features:

A: Sine waveform output

B: Manual PW on main square output

C: PWM input and attenuator for main square wave output.

7 simultaneous waveform outputs spreading 4 octaves!

$ TBD

Info

Current draw of version 1:

Initial warm up (first minute):

V+= 93.6mA

V-= 42.2mA


After warm up:

V+= 73.2mA

V-= 42.0mA

Retrieved from "https://mattsonminimodular.com/wiki/index.php?title=Voltage_Controlled_Oscillator_-_Jack_Version&oldid=1483"